SEARCH BY INSPIRATIONS
- Air filters
- Brake & Clutch levers
- Electric box
- Exhaust
- Fenders
- Footpegs
- Front protections
- Front suspension
- Front suspension protections
- Fuel tanks
- Handle grips
- Handlebar
- Handlebar switch controls
- Headlights
- License plate holder
- Mirrors
- Mudguards
- Rear frame
- Suspensions
- Seats
- Silencers
- Speedometers
- Taillights
- Thermal strips
- Turn signals
- Air filters
- Belows front suspensions
- Brake & clutch levers
- Electric box
- Engine protection
- Exhaust
- Fenders
- Foot pegs
- Front suspensions
- Fuel tanks
- Handle grips
- Handlebar switch controls
- Handlebars
- Headlights
- License plate holder
- Mirrors
- Mudguards
- Rear frame
- Rear light
- Rear suspensions
- Seats
- Silencers
- Speedometers
- Thermal strips
- Turn signals
- Air filters
- Belows front suspensions
- Brake & Clutch levers
- Electric box
- Exhausts
- Fenders
- Foot pegs
- Front suspensions
- Fuel tanks
- Handle grips
- Handlebar switch controls
- Handlebars
- Headlights
- License plate holders
- Mirrors
- Mudguards
- Rear light
- Rear suspensions
- Seats
- Silencers
- Speedometers
- Thermal strips
- Turn signals
- Air filters
- Belows front suspension
- Brake & Clutch levers
- Electric box
- Exhaust
- Fenders
- Foot pegs
- Front protection
- Front suspensions
- Fuel tanks
- Handle grips
- Handlebar switch controls
- Handlebars
- Headlights
- License plate holders
- Mirrors
- Mudguards
- Rear frame
- Rear light
- Rear suspensions
- Seats
- Silencers
- Speedometers
- Thermal strips
- Turn signals
- Air filters
- Belows front suspensions
- Brake & Clutch levers
- Electric box
- Engine protection
- Exhausts
- Fenders
- Foot pegs
- Front suspensions
- Fuel tanks
- Handle grips
- Handlebar switch controls
- Handlebars
- Headlights
- License plate holders
- Mirrors
- Mudguards
- Rear frame
- Rear light
- Rear suspensions
- Seats
- Silencers
- Speedometers
- Thermal strips
- Turn signals
SEARCH BY MOTORCYCLE BRAND
Installation & Safety Notice – Long-Fender Plate Holder for Triumph Bobber
Designed for Triumph Bobber (2017 »). Regulations differ by region—follow the guidelines below.
| Region | Rule | Your Checklist |
|---|---|---|
| USA | FMVSS 108 & local DMV | Plate angle 0–30° vertical & ≥ 12″ (305 mm) from road. Keep OEM tail/stop lamp & turn-signals fully visible 45° L/R. LED bolt lights (SAE L) must be wired to tail-lamp circuit. |
| EU / UK | UNECE R50 & R (plate) tilt ≤ 30° | Use 180 × 200 mm adapter for EU plate size if required. Confirm rear reflector remains unobstructed. |
| Australia / NZ | ADR 61/02 | Plate centre ≥ 300 mm height, ≤ 15° tilt. Illuminated & legible 20 m. |
Universal Fitting Instructions
- Tighten M6 stainless bolts to 10 N·m (89 lbf·in) with Loctite 243.
- Maintain ≥ 20 mm gap between plate edge & tyre at full suspension compression.
- Route LED bolt wires along OEM harness; seal connectors with heat-shrink.
- Re-torque fasteners after 100 km / 60 mi.
⚠️ Incorrect installation or obscured lamps can lead to accidents and fines. Ensure compliance with your local vehicle code.
⚠️ California Proposition 65: This product can expose you to chemicals including hexavalent chromium. See P65Warnings.ca.gov.